Many car owners don’t like the idea of having to drill holes into the front of their brand-new car’s bumper to mount a front license plate, but thankfully there are other alternatives such as adhesive plates and magnetic mounts. If your vehicle is not manufactured with a way to mount a front license plate, then it is your responsibility to take it into your own hands My Vehicle Does Not Have a Place for the Front Plate The plates must be securely fastened to prevent swinging, clearly visible, and clearly legible. As a result, it is a law in California to have both front and fear license plates even if your vehicle is not manufactured with a front license plate mount. For passenger vehicles, two license plates are issued. Under the California Vehicle code §5200, “when two license plates are issued by the department for use upon a vehicle, they shall be attached to the vehicle for which they were issues, one in the front and the other in the rear”. If your vehicle is not manufactured with a front license plate mount does that mean that a front license plate isn’t required in California? However, oddly enough it is a growing trend for newer cars, such as a Tesla, to be manufactured without a way to mount a permanent front license plate. This law requires front and rear temporary plates. Effective date: September 1, 2013.Beginning in 2019, any car that was purchased or leased is required to have temporary license plates the moment the vehicle is driven off the lot. I'd avoid getting one of those, due to an amendment to Texas' Transportation Code in 2013: (2) if the person uses a license plate flipper before, during, or after the commission of an offense to avoid identification or detection for the offense for which the license plate flipper was used, the offense is one category higher than the most serious offense that was committed, and if the most serious offense is a Class A misdemeanor, the offense is a state jail felony, except that if the most serious offense is a felony of the first degree, the offense is a felony of the first degree. (1) an offense is a Class A misdemeanor if the person distributes, manufactures, sells, or otherwise furnishes a license plate flipper to another If your vehicle is a motorcycle, tractor truck. Place the plates on the front and rear of your vehicle so that they are securely fastened and clearly visible, and place the validation sticker on the rear plate. (c) Provides that an offense under Subsection (b) is a Class B misdemeanor, except that: DMV will issue you two license plates, a validation sticker showing the expiration date, and a registration card. (b) Provides that a person commits an offense if the person possesses a license plate flipper as defined in Subsection (a). Amends Chapter 504, Transportation Code, by adding Section 504.946, as follows: Additionally, if a license plate flipper is used to avoid detection before, during, or after commission of a crime, the offense becomes punishable by one category higher than the most serious offense committed. Texas SB 1757 makes possession of a license plate flipper an offense punishable by Class B misdemeanor, and it creates an offense punishable by Class A misdemeanor for distribution, manufacture, selling, or furnishing a license plate flipper. Placement or mounting of license plates is not defined." - .usĬlick to expand.I'd avoid getting one of those, due to an amendment to Texas' Transportation Code in 2013: State law requires that you display two (2) license plates, one to the front and one to the rear. "How Many License Plates Am I Required To Display? Probably not at the legal height for some states but in Texas its not defined. I was originally going to grind it down so I could mount it flush but decided to angle the top so that air could still flow around it. Will have to see if it causes any thermal issues over the summer. I can post more details if anyone is interested. But that did not go so well so used a grinding wheel to shave a little off the top & bottom. I was originally going to roll the edges of the plate a bit to make it fit. I got the ideas from other BMW sites and did not see exactly what I wanted so came up with this.įor the top I used a modified Bell mount, took out center bits, secured with toggle bolts from Home Depot. The dealer was going to drill holes in the bumper. Here in Texas we are unfortunately required to display a front license plate and they have recently been enforcing it with no warnings given.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |